Cisco receiver is getting ais
- Cisco receiver is getting ais software#
- Cisco receiver is getting ais code#
- Cisco receiver is getting ais series#
Cisco receiver is getting ais software#
If the PRI in local alarm was a primary clock source, the software switches the clock controller to the secondary reference.Ĭheck the Clock Controller is enabled and locked.Ĭonfiguration settings do not match the far end. Verify the wiring, and physical connection integrity.
![cisco receiver is getting ais cisco receiver is getting ais](https://cdn.shopify.com/s/files/1/0347/7127/1815/products/86310XL_1024x1024.jpg)
The channels will be disabled, the PRI will be in local-alarm mode.)įar-end problems, usually indicated by a remote alarm.Ĭheck PRI status, and your local transmit pair integrity.Ĭontact the far end to determine what action they are taking.
![cisco receiver is getting ais cisco receiver is getting ais](https://cdn.eventidecommunications.com/uploads/2020/11/NexLog-840DX-With-Dispay-Front-FINAL-22Sept2020_0-1024x369.png)
(If you are not physically connected to the far end, frame-alignment errors occur. Determine the cause of the problem and follow the recommended actions: The PRI can have any of the following problems. A minimum persistence time is defined in LD 73. Grade-of-service is changed based on the duration of the alarm within a defined period of time. Group 2 alarms are either continuous or discontinuous. The threshold count is determined in LD 73. Grade-of-service is changed based on how quickly the threshold of the counter is exceeded. Group 1 alarms are event-driven and include indicators that decrement a counter whenever an error is detected. LD 17: CHG OVLY, BKGD 60 (LD 22: PRT OVLY). Use during maintenance, when the circuit would otherwise be automatically disabled due to excessive slips. Note: LD 60 as a background task, will periodically (~45 seconds) display and reset the alarm counters.
![cisco receiver is getting ais cisco receiver is getting ais](https://i.ebayimg.com/images/g/FwkAAOSwQ-JebD06/s-l1600.jpg)
When the alarm is cleared, the PRI is automatically restored to service, and B-channels enabled.Ĭheck the PRI Status and reset the counters in LD 60: Red: Near End Alarm (NEA) When a Red alarm occurs, all B-channels are disabled.
![cisco receiver is getting ais cisco receiver is getting ais](https://i.ebayimg.com/images/g/p4sAAOSwTO9eC6N9/s-l300.jpg)
Any help would be greatly appreciated.Red Alarm = nothing received, so check RX Line code, framing, etc are set as per Verizon's specs. Inserting a hard loop cable in the interface clears the alarm. The Alarm LED is lit as soon as we plug into the wall jack that goes to the smart card. Verizon has run loopback tests from their office and claim to "see" this router.
Cisco receiver is getting ais code#
Version info Firmware: 20000922, FPGA: 15įraming is ESF, Line Code is B8ZS, Clock Source is Line.ĭata in current interval (0 seconds elapsed):Ġ Line Code Violations, 0 Path Code ViolationsĠ Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded MinsĠ Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs We need to connect this to a leased T1 line from Verizon.
Cisco receiver is getting ais series#
I am trying to configure a Cisco VWIC-2MFT-T1-D1 interface card in a cisco 2600 series router.